SpECtite Polyurea H

LIQUID APPLIED POLYUREA HYBRID MEMBRANE

SpECtite Polyurea H is a two part, elastic, 100% solids, very fast curing and coloured polyurea hybrid liquid applied membrane with good chemical resistance. Suitable for use in hot and tropical climatic conditions.

Product Videos

Technical Details

SpECtite Polyurea H may only be used by experienced professionals.

On concrete:
• Waterproofing on walkways and balconies.
• Waterproofing on floors and car park decks.
• Water retaining structures in power plants.
• Secondary containment structures.
• Tank, bund and pit lining in sewage and waste water treatment plants.
• Waterproofing on concrete bridge decks, membrane underneath hot rolled asphalt, certified in accordance to BBA/HAPAS.
• Waterproofing on concrete bridge decks, membrane underneath mastic asphalt, tested in accordance to ETAG 033.
• Waterproofing for cut and cover structures.
• Waterproofing for submersed structures.

On steel:
• Truck bed lining.

• Good abrasion resistance
• Excellent crack bridging properties
• Moderate chemical resistance
• Almost immediate return-to-service time
• Applicable in temperatures from -10 °C to +50 °C
• Performs in constant dry temperatures from -30 °C to+100 °C
• Very fast reactivity and curing time

Appearance (Part A)	Various
Density (Part A)	1.03 kg/l
Appearance (Part B)	Clear Yellowish
Density (Part B)	1.11 kg/l
Viscosity @ 20°C (Part A)	900 – 1300 cp
(Part B)	600 – 850 cp
Viscosity @ 25°C (Part A)	~750 cp
(Part B)	500 cp
Tensile Strength (DIN 53504)	9 ± 2 N/mm²
Elongation at Break (DIN 53504)	300 ± 25 %
Shore A Hardness (DIN 53505)	80 ± 5
Abrasion Resistance CS17/1000g/1000cy (ISO 5470-1)	10 – 15 mg
Crack Bridging Ability Class A5	Static
Chemical Resistance	De-icing Salts
	Bitumen
	Allkalis
	Fresh & Ground Water
	Various Chemicals
Mixing Ratio Part A : Part B (Volume)	1 : 1
Product Temperature	> +65°C
Relative Humidity	<85%
Gel Time	12 sec at +20°C
Waiting Time	1 – 2 min at +20°C

Surface Preparation
The surface must be sound, of sufficient strength, clean, dry and free of dirt, oil, grease and other contamination. The substrate must be primed with SpECtite Primer EP121 epoxy primer prior to application of SpECtite Polyurea H. SpECtop NS Grains may be broadcasted over the primer for better adhesion properties if required.

Substrate Quality
The concrete substrate must be sound and of sufficient compressive strength (minimum 25 N/mm2) with a minimum pull off strength of 1.5 N/mm2. The substrate must be clean, dry and free of all contaminants such as dirt, oil, grease, coatings and surface treatments, etc. Concrete substrates must be pre-pared mechanically using abrasive blast cleaning or scarifying equipment to remove cement laitance and achieve an open textured surface.

Weak concrete must be removed and surface defects such as blow holes and voids must be fully exposed. Repairs to the substrate, filling of blowholes/voids and surface levelling must be carried out using appropriate products from SpEC. All dust, loose and friable material must be completely removed from all surfaces before application of the product, preferably by brush or vacuum.

Application
Dose and mix with a suitable air driven or electrical plural component heated spray equipment. Both components must be heated up to minimum +70°C. The accuracy of mixing and dosage must be controlled regularly with the equipment. Thoroughly stir part A using a drum stirrer until a homogenous colour is obtained. Spray trial should be done before commencing any work to setup spray equipment properly.

SpECtite Polyurea H is supplied in:
Part A = 205 kg drums
Part B = 222 kg drums

The coverage rate for SpECtite Polyurea H is 1.06 kg/m²/mm (approx.).

Layer thickness 1.5 mm – 2 mm